| Kode-M | Deskripsi |
|---|
| M00 | Stop Program – Modal |
| M01 | Stop Program Opsional – Modal |
| M02 | Akhir Program – Modal |
| M03 | Spindel ON Maju (S) – Modal |
| M04 | Spindel ON Mundur (S) – Modal |
| M05 | Spindel Stop – Modal |
| M08 | Pendingin ON – Modal |
| M09 | Pendingin OFF – Modal |
| M10 | Klem Chuck – Modal |
| M11 | Buka Klem Chuck – Modal |
| M12 | Jet Udara Otomatis ON (P) – Modal/Opsional |
| M13 | Jet Udara Otomatis OFF – Modal/Opsional |
| M14 | Klem Spindel Utama – Modal/Opsional |
| M15 | Buka Klem Spindel Utama – Modal/Opsional |
| M17 | Putar Turunan Maju (T) – Modal |
| M18 | Putar turunan Mundur (T) – Modal |
| M19 | Orientasi Spindel – Modal/Opsional Contoh |
| M21 | Maju Tongkat Penguat – Modal/Opsional |
| M22 | Tarik Tongkat Penguat – Modal/Opsional |
| M23 | Sudut Keluar dari Benang ON – Modal |
| M24 | Sudut Benang OFF – Modal |
| M25-M28 | Antarmuka Kode M Pengguna Opsional dengan Sinyal M-Fin – Modal |
| M30 | Akhir Program dan Reset – Modal |
| M31 | Majukan Auger Keripik – Modal |
| M33 | Hentikan Auger Keripik – Modal |
| M36 | Penangkap Bagian ON – Modal/Opsional |
| M37 | Penangkap Bagian OFF – Modal/Opsional |
| M38 | Variasi Spindel ON – Modal |
| M39 | Variasi Spindel OFF – Modal |
| M41 | Override Gigi Rendah Spindel – Modal |
| M42 | Override Gigi Tinggi Spindel – Modal |
| M43 | Buka Kunci Turunan – Modal |
| M44 | Kunci Turunan – Modal |
| M51-M58 | Set Kode M Pengguna Opsional – Modal |
| M59 | Set Relay Output (N) – Modal |
| M61-M68 | Bersihkan Kode M Pengguna Opsional – Modal |
| M69 | Bersihkan Relay Output (N) – Modal |
| M76 | Tampilan Program Tidak Aktif – Modal |
| M77 | Tampilan Program Aktif – Modal |
| M78 | Alarm dalam Sinyal Skip Ditemukan – Modal |
| M79 | Alarm jika Sinyal Skip Tidak Ditemukan – Modal |
| M85 | Pintu Otomatis Buka – Modal/Opsional |
| M86 | Pintu Otomatis Tutup – Modal/Opsional |
| M88 | Pendingin Tekanan Tinggi ON – Modal/Opsional |
| M89 | Pendingin Tekanan Tinggi OFF – Modal/Opsional |
| M93 | Mulai Tangkapan Posisi Sumbu – Modal/Opsional |
| M94 | Hentikan Tangkapan Posisi Sumbu – Modal/Opsional |
| M95 | Mode Tidur – Modal |
| M96 | Lompat jika tidak ada Sinyal – Modal |
| M97 | Panggilan Sub-Rutine Lokal – Modal |
| M98 | Panggilan Sub-Program – Modal |
| M99 | Kembali Sub-Program / Rutine atau Loop – Modal |
| M109 | Input Pengguna Tidak Aktif (P) – Modal/Opsional |
| M110 | Klem Chuck Tongkat Penguat – Modal/Opsional |
| M111 | Buka Klem Chuck Tongkat Penguat – Modal/Opsional |
| M119 | Orientasi Spindel Sekunder – Modal/Opsional** |
| M121-M128 | Antarmuka Kode M Pengguna Opsional dengan Sinyal M-Fin – Modal |
| M133 | Live tool Drive Maju (P) – Modal/Opsional Contoh |
| M134 | Live Tool Drive Mundur (P) – Modal/Opsional |
| M135 | Live Tool Drive Stop – Modal/Opsional |
| M143 | Spindel Sekunder Maju (P) – Modal/Opsional |
| M144 | Spindel Sekunder Mundur (P) – Modal/Opsional |
| M145 | Spindel Sekunder Stop – Modal/Opsional |
| M154 | C Axis Engage – Modal/Opsional Contoh |
| M155 | C Axis Disengage – Modal/Opsional |
| M164 | Putar Pegang APL Ke Posisi “n” – Modal/Opsional |
| M165 | Buka Pegang APL 1 (Bahan Baku) – Modal/Opsional |
| M166 | Tutup Pegang APL 1 (Bahan Baku) – Modal/Opsional |
| M167 | Buka Pegang APL 2 (Bahan Jadi) – Modal/Opsional |
| M168 | Tutup Pegang APL 2 (Bahan Jadi) – Modal/Opsional |
